KONE escalators rely on multiple electrical, mechanical, and safety monitoring systems to maintain stable operation. When an abnormal condition occurs, the escalator may stop or trigger a protective function to prevent further operation.
Understanding the fault symptoms and knowing which components to inspect can help maintenance technicians identify potential problems more efficiently.
This guide covers 13 common KONE escalator faults and their corresponding troubleshooting methods, including motor starting failures, reverse rotation, speed monitoring faults, step missing protection, brake protection, and anti-reversal protection.
1. Motor Does Not Run (External Power Supply ON)
Fault Description:
The external power supply is switched on, but the escalator motor does not start.
Troubleshooting and Solutions:
1. Check whether the safety circuit is functioning correctly. The safety relay, contactors, and corresponding PLC or single-board controller input points can help identify the problem. If an LCD fault message is displayed, refer to the corresponding fault information.
2. Check whether the JXW phase-sequence indicator is operating normally.
3. Check whether the OCR thermal overload relay contacts are functioning correctly.
2. Motor Runs in the Reverse Direction
Fault Description:
The escalator motor rotates in the opposite direction to the commanded direction.
Troubleshooting and Solutions:
1. Check the wiring associated with the U or D contactor.
2. Check whether the motor wiring has been interchanged. The original technical reference specifies that when changing the motor winding connections, the corresponding winding terminals must be adjusted together. Follow the actual motor wiring diagram.
3. Check whether the direction command signal is abnormal.
3. Main Drive Speed Monitoring Protection
Fault Description:
The main drive speed monitoring system detects an abnormal condition.
Troubleshooting and Solutions:
1. Check the voltage and signal outputs of the main drive speed sensor. A replacement sensor can be used for comparison when diagnosing a suspected sensor fault.
2. Check whether the associated speed sensor wiring is correctly connected.
3. Check whether the motor power supply is abnormal.
4. Handrail Speed Monitoring Protection
Fault Description:
The handrail speed monitoring system detects an abnormal operating condition.
Troubleshooting and Solutions:
1. Check the voltage and signal outputs of the handrail speed sensor. A replacement sensor can help determine whether the original sensor is faulty.
2. Check whether the handrail speed sensor wiring is correctly connected.
5. Missing Step Protection
Fault Description:
The escalator’s missing-step monitoring system detects an abnormal condition.
Troubleshooting and Solutions:
1. Check the voltage and signal outputs of the missing-step detection sensor. A replacement sensor can be used to help identify a sensor fault.
2. Check whether the missing-step sensor wiring is correctly connected.
6. Contactor Contact Sticking Protection
Fault Description:
The controller detects an abnormal contactor condition.
Troubleshooting and Solutions:
Check whether the U, D, Y, Δ, and JBZ contactors are mechanically stuck, jammed, or failing to operate properly.
7. Brake Release Protection
Fault Description:
The brake release monitoring system detects an abnormal condition.
Troubleshooting and Solutions:
Check whether the service brake releases normally. Inspect the associated detection switch for sticking or mechanical malfunction.
8. Photoelectric Energy-Saving System Failure
Fault Description:
The photoelectric energy-saving system fails to operate normally.
Troubleshooting and Solutions:
1. Check the voltage and signal outputs of the photoelectric sensor. Pay particular attention to possible inverter interference and whether the grounding connections are properly installed.
2. Check whether the photoelectric sensor wiring is correctly connected.
9. Buzzer Fault
Fault Description:
The escalator buzzer does not operate normally.
Troubleshooting and Solutions:
1. Check the voltage supply and wiring of the buzzer relay. Replacing the buzzer relay can help determine whether it is faulty.
2. Check the buzzer voltage supply and wiring. Replacing the buzzer can help identify a defective unit.
10. Direction Indicator Abnormality
Fault Description:
The escalator direction indicator does not operate normally.
Troubleshooting and Solutions:
1. Check the voltage supply and wiring of the direction indicator relay. Replacing the relay can help determine whether it is faulty.
2. Check the voltage supply and wiring of the direction indicator itself. Replacing the indicator can help identify a defective unit.
11. Automatic Operation Time Too Short or Too Long
Fault Description:
The automatic operating time is shorter or longer than expected.
Troubleshooting and Solutions:
1. Modify the relevant time parameters in the PLC program.
2. Perform the self-learning operation, which can automatically adjust the relevant time parameters.
12. Anti-Reversal Protection
Fault Description:
The escalator operates normally in the downward direction. However, when operating upward, the escalator stops due to protection activation, and the safety brake is triggered.
Troubleshooting and Solutions:
1. Check whether the anti-reversal switch is operating smoothly or has been adjusted incorrectly.
2. Check whether the wiring of the anti-reversal detection switch is properly connected.
13. Safety Brake Activation
Fault Description:
The escalator safety brake is activated.
Troubleshooting and Solutions:
1. Check the wiring and installation of the main drive speed sensor.
2. Check whether the drive chain switch wiring is loose.
3. Check the anti-reversal switch, particularly when the safety brake is activated during upward operation.
Conclusion
KONE escalator troubleshooting involves several interconnected systems, including motor control, speed monitoring, handrail monitoring, step detection, brake protection, and safety circuits.
By identifying the fault symptom and inspecting the corresponding sensors, contactors, wiring, and control signals, maintenance technicians can narrow down the possible source of an abnormal condition.
For maintenance and repair work, always follow the applicable escalator electrical diagrams, controller documentation, and safety procedures.
Post time: Nov-16-2026
